收藏本站
Not Recommended for New Designs
Application Information (continued)
OVP – Overvoltage Protection
The output Overvoltage Protection set point of the P048F048T12AL is
factory preset for 56 V. If this threshold is exceeded the output shuts
down and a restart sequence is initiated, also indicated by PC pulsing.
If the condition that causes OVP is still present, the unit will again shut
down. This cycle will be repeated until the fault condition is removed.
The OVP set point may be set at the factory to meet unique high
P048F048T12AL
Adjusting Current Limit
The current limit can be lowered by placing an external resistor
between the I L and SG ports (see Figure 20 for resistor values) . With
the I L port open-circuit, the current limit is preset to be within the
range specified in the output specifications table on Page 4.
voltage requirements.
1000
33uF (ESR >= 0.85Ω) & 47uf (ESR>= 0.60Ω) - NO IL TRIM
PRM Output Power Versus VTM Output Power
22uF (ESR >=1.2Ω)
? ?
As shown in Figure 19, the P048F048T12AL is rated to deliver 2.5 A
maximum, when it is delivering an output voltage in the range from
100
10uF (ESR >= 2.40Ω)
26 V to 48 V, and 120 W, maximum, when delivering an output
voltage in the range from 48 V to 55 V. When configuring a PRM for
use with a specific VTM, refer to the appropriate VTM data sheet. The
VTM input power can be calculated by dividing the VTM output power
by the VTM efficiency (available from the VTM data sheet). The input
10
0uF
power required by the VTM should not exceed the output power rating
of the PRM.
1
75%
80% 85% 90% 95%
% Percentage of Current Limit Setpoint
100%
2.55
2.50
2.45
2.40
Figure 20 — R IL vs percentage of current limit. Shaded areas shown
minimum valid R IL as a function of load capacitance and ESR.
Input Fuse Recommendations
2.35
2.30
2.25
2.20
2.15
0
Safe Operating Area
~ ~
20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60
Factorized Bus Voltage (V f )
A fuse should be incorporated at the input to the PRM, in series with
the +In port. A fast acting fuse, NANO2 FUSE 451/453 Series 10 A
125 V, or equivalent, may be required to meet certain safety agency
Conditions of Acceptability. Always ascertain and observe the safety,
regulatory, or other agency specifications that apply to your specific
application.
Product Safety Considerations
If the input of the PRM is connected to SELV or ELV circuits, the output
of the PRM can be considered SELV or ELV respectively.
Figure 19 — P048F048T12AL rating based on Factorized Bus voltage
The Factorized Bus voltage should not exceed an absolute limit of
55 V, including steady state, ripple and transient conditions. Exceeding
this limit may cause the internal OVP set point to be exceeded.
Parallel Considerations
The PR port is used to connect two PRMs in parallel to form a higher
power array. When configuring arrays, PR port interconnection
terminating impedance is 10 k to SG. See note Page 8 and refer to
Application Note AN002. Additionally one PRM should be designated
as the master while all other PRMs are set as slaves by shorting their
SC pin to SG. The PC pins must be directly connected (no diodes) to
assure a uniform start up sequence. Consult Vicor applications
engineering for applications requiring more than two PRMs.
If the input of the PRM is connected to a centralized DC power system
where the working or float voltage is above SELV, but less than or
equal to 75 V, the input and output voltage of the PRM should be
classified as a TNV-2 circuit and spaced 1.3 mm from SELV circuitry or
accessible conductive parts according to the requirements of
UL60950-1, CSA 22.2 60950-1, EN60950-1, and IEC60950-1.
Applications Assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicorpower.com.
PRM ? Regulator
Page 10 of 14
Rev 3.1
12/2013
vicorpower.com
800 735.6200
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
A9BBA-0804F FLEX CABLE - AFF08A/AF08/AFF08A
EEV-HA1HR22R CAP ALUM 0.22UF 50V 20% SMD
P045F048T32AL-CB V.I CHIP PRM REGULATOR EVAL BOAR
P045F048T17AL-CB V.I CHIP PRM REGULATOR EVAL BOAR
A9BBA-0905F FLEX CABLE - AFF09A/AF09/AFF09A
RO-1215S/P CONV DC/DC 1W 12VIN 15VOUT
RO-1209S/P CONV DC/DC 1W 12VIN 09VOUT
R1S-2412-R CONV DC/DC 1W 24VIN 12VOUT
相关代理商/技术参数
P048F048T24AL 功能描述:REGULATOR PRM 48V OUT 240W SMD RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, PRM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
P048F048T24AL_1 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:PRM Regulator
P048F048T24AL-CB 功能描述:EVALUATION BOARD PRM REGULATOR RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, PRM™ 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND
P048F048T24AL-CC 功能描述:PRM REGULATOR CONSTANT EVAL BOAR RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, PRM™ 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND
P048K048M24AL 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - PRM-AL Pre-regulator Module
P048K048T24AL 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VI Chip - PRM-AL Pre-regulator Module
P048T048M12AL 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:PRM Regulator
P048T048M24AL 功能描述:V.I CHIP PRM REGULATOR 48V 240W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, PRM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）